nutribullet blender combo blinking blue light

After that, you can try pulling the lip back to the actuator. Place your screwdriver beside the cup and push the cup away from the base. ( Source)ĭon’t fret if you happen to be the victim – use a screwdriver with a flat tip to turn the cup so that it aligns with the actuator. This often occurs when one of the lips goes under the white actuator. Simply unstuck your NutriBullet from the motor base. Cup Stuck to Base of Nutribullet – What to Do? If you’re still having problems pressing on them even after several attempts, please contact NutriBullet’s support or find a replacement. You can repeat this process several times until you find them effective. Soak the plastic activators into the mixture, after which, you should be able to press on them without any hassle. If you don’t find them effective, vinegar, cooking oil, and hot water can come in handy to help moisten the activators. These activators should be flexible enough to move down upon pressing on them. To deal with this problem, use the plastic activators that come with the NutriBullet. More often, jamming occurs when accumulated food debris builds up between the latch and the cup. How Do You Fix a Jammed NutriBullet?įinding the solution to a jammed NutriBullet can be daunting. If the blade can’t connect properly, it might be time to find a replacement. Make sure to secure it tightly so that liquids don’t come out upon running the NutriBullet. Often, your NutriBullet will be prone to leakages if the extractor blade is loosely attached. As a result, your NutriBullet starts leaking. Once the seal starts failing, the extractor blade will find it difficult to attach itself to the cup. The extractor blade includes a rubbery gasket seal underneath it. You don’t need to replace the entire NutriBullet, but the cracked components. Regardless of the cracks’ position, they will always find a way to pour out your ingredients. Not only that, you’ll be straining the blades too. While this sounds obvious, you’re exposing your NutriBullet to potential damages.

You’re running out of time, so you want to blend all your ingredients at once. The following reasons may cause your NutriBullet to leak: Leakages are always a bad sign to your NutriBullet. It’s recommended to do the blending in intervals to prevent the motor from burning out. Therefore, if the motor suddenly stops working, it could be because you ran the blender longer. Usually, it’s the motor that runs the NutriBullet’s blades. Most importantly, deep clean the edges to deal with this problem once and for all. Occasionally clean the blades in between uses to prevent the accumulation of food debris. You can as well use it for liquid substances. As such, heavy solids might be strenuous to your NutriBullet, forcing the blades to stop. The NutriBullet is recommended for softer foods such as veggies and fruits. Going past that will mean creating a jam, and as such, the blades won’t cut at all. So what happens if the blades won’t turn completely? There are many reasons for this, so let’s discuss them further.Įlectronic appliances such as blenders and electric kettle often include a recommended fill line. You can always replace the old blades with new ones for a more enhanced cutting. As mentioned earlier, this is an easy fix, so you don’t have to worry. This could possibly result from old blades that have become blunt. Often, the motor will run as usual, but the final products will end up partially cut. Blade IssuesĪ) The Blades May Only Partially Cut Foodįortunately, this, too, is a simple fix. You might be surprised to find out that the blender needed a simple fix. You can also check whether your NutriBullet is plugged incorrectly. Components such as lids, cups, and lip rings are dishwasher-safe except for the motor base. To maintain your NutriBullet’s elements, don’t toss it in the dishwasher. You may also want to dislocate the NutriBullet’s casing to check on the internal parts and whether they are exposed. If your NutriBullet stops working midway, switch it off or unplug immediately from the main switch.

The wires might be exposed too, which is a safety threat. First, it could be that your blender is exhausted that some components have lost their performance. While this isn’t your fault, there are a few things to blame. It can be downright frustrating if your blender stops working in the middle of blending your favorite smoothie. This article categorizes all NutriBullet failures based on the blender, the blades within, and the leakages to help you find solutions to your frustrations. Normally, your NutriBullet not working could be due to user error or with time and age. Cleaning the Nutribullet Cup and Bladesģ Common Reasons For Nutribullet Not Working Cup Stuck to Base of Nutribullet – What to Do?.3 Common Reasons For Nutribullet Not Working.

Nutribullet blender combo blinking blue light